What size are my U-joints?

U-Joint Sizes

What series is a 331 U joint?

This is a NEW 1350 Series replacement Universal Joint that fits a variety of 1957-2015 General Trucks and some Corvette rear axle shafts. It is fully greasable and ready to install in your drive shaft to replace old, worn out joints.

What is a 1480 U joint?

Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway. …

What is a 1310 series U joint?

1310 U-Joint Series is the most common U-Joint ever used. It is still used on OE applications. 1.062 cap and 3.219 width. ( 1 1/16 x 3 1/4 close) 1330 U-Joint Series is very common and used on OE production.

What is the difference between a 1350 and 1410 u-joint?

1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications. The two joints split the angle, allowing for greater angularity.

What does a 534G U-joint fit?

question_answer Ask us a Question Fitment U-Joint moog-534g fits these vehicles: Buick Centurion 1971 thru 1973. Buick Century 1973 thru 1981. Buick Commercial Chassis 1991 thru 1996.

How strong is a 1310 U joint?

1,600 lb-ft
The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque. While the 1310 series, the stock size for most Jeeps, is rated for 1,600 lb-ft of torque.”

What is the difference between 1310 and 1350 u-joint?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

What is the difference between a 1310 and 1350 u-joint?

What is the difference between 1330 and 1350 u-joint?

The 1310 series u-joint measures approximately 3 1/4 inches wide. The 1330 and 1350 both measure approximately 3 5/8 wide. The 1350 series has a cap diameter of 1 3/16 inch and the body and journals are bigger than the 1310 or 1330.

How to determine Moog universal joint part number?

Using the online catalog database, MOOG ® makes it easy to correctly determine a replacement MOOG universal joint part number. Here’s what you need to get started: Tip: Measure two adjacent caps even if they’re the same style in case they are different sizes. Step 3: Measure U-joint assembly.

Which is better Moog precision or Moog driveline?

Precision super strength u joints symptoms of bad u joints suspension moog super strength u joint 295 moog driveline s greaseable mo331 moog u joint Er U Joint Lication Chart Mosad Parkersydnorhistoric

What’s the best way to replace a Moog U-joint?

Welded plate bearings: Remove grease boots and ensure caps are fully seated by applying light pressure using a C-clamp or a vise at both ends of cups (tight enough that the u-joint cross body can be turned by hand). Measure the distance between the opposite plates. Don’t include the plate thickness in the measurement.

How do you measure the bearings on a Moog?

Measure the distance between the opposite plates. Don’t include the plate thickness in the measurement. Winged bearings: Measure the distance between the holes directly across from each other and the pilot diameter. Make sure to take note of the style of the wings as there are many variations.

What size are my U joints?

U-Joint Sizes

What are the different types of U joints?

The u-joint is one of the oldest of all flexible couplings. It is commonly known for its use on automobiles and trucks. A universal joint in its simplest form consists of two shaft yokes at right angles to each other and a four-point cross that connects the yokes….TECH TALK: A LITTLE INFORMATION ABOUT U-JOINTS.

What are the strongest U joints?

Registered. 1410s would be the strongest, most common u-joint you can find.

Where are the U joints located?

U-joints are found on each of the ends of the rear drive shaft, whereas CV-joints are found on front wheel drive cars. Each allows the drive shaft to rotate as the differential moves in relation to the rest of drive train mounted on the chassis.

What is a 1480 U-joint?

Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway. …

Will a stiff u-joint cause vibration?

Drive line vibration, after u-joint replacement, is usually the result of a u-joint not properly posi- tioned, or yoke ears which are binding. In either case the problem can usually be pin pointed by articulating the drive shaft. The replacement u-joint, even though centered, could cause the shaft to vibrate.

What causes U-joints to break?

This usually happens because of corrosion, excessive jolting or vibration, or because the bolts were not properly torqued into place. A worn or cracking transmission or differential housing can also cause this. Of course, u-joint failure isn’t limited to these three causes.

What kind of U-joints do Summit Racing use?

Replace your worn factory steering U-joint or finish off your custom steering system with top-brand U-joints from Summit Racing! We’ve got steel, stainless steel, aluminum, and chromoly steering shaft universal joints in a variety of sizes and spline counts.

What kind of steel is used in U-joints?

U-joints are used to connect two shafts that have a high amount of misalignment. These U-joints are made of steel or zinc. Made of stainless steel, these U-joints offer excellent corrosion resistance. These U-joints are made of steel or plastic.

What kind of material are universal joints made of?

These U-joints are made of steel or plastic. These steel U-joints meet MIL-U-20625A Class A and have hardened yoke ears for added strength and durability. Made of stainless steel, these U-joints offer excellent corrosion resistance. They also meet MIL-U-20625A Class A. These U-joints are made of steel.

Which is the widest angle for a U-joint?

Single U-Joints A set of gears transmit rotary motion at angles up to 136°— the widest angle of all our U- joints. They are for hand- powered, low-speed applications.